Product – Mayr – Acessories |
 |
Limit Switch (Mechanical)
This device is used to monitor mechanical movements and end positions. It is a controlling sensor for electronic and mechanical sequences. It also registers axial disengaging movements, e.g. on EAS-clutches. |
Limit Switch (Contactless)
This device is used for measuring and monitoring axial and radial disengaging movements, e.g. on EAS-clutches. It acts as a control sensor for electronic and mechanical sequences. |
Limit Switch (Contactless, Magnetic Field-resistant)
Magnetic field-resistant or welding-resistant proximity switches are used where strong magnetic fields can influence the function of the proximity switch. For example, they can be used in the field of strong magnetic coils as well as welding guns or welding electrodes with high welding currents. |
Limit Switch (Contactless, with Mounting Flange)
The inductive proximity switch monitors and detects operating conditions on EAS overload clutches. Axial movements caused by overload or switching procedures are registered by the proximity switch. The signal can be used for further process controlling e.g. for drive switch-off. |
Limit Switch (Mechanical, Multi-directional)
The limit switch is used to monitor and measure axial or radial mechanical movements and adjustments e.g. on EAS-clutches. The device is suitable for clutches with a minimum stroke of 1.1 mm with radial actuation and 0.9 mm with axial actuation. |
 |
EAS-Sm/Zr Control Unit
This device is used to monitor mechanical movements and end positions. It is a controlling sensor for electronic and mechanical sequences. It also registers axial disengaging movements, e.g. on EAS-clutches. |
EAS-Sp Control Unit
This device is used for measuring and monitoring axial and radial disengaging movements, e.g. on EAS-clutches. It acts as a control sensor for electronic and mechanical sequences. |
Half-wave Rectifiers and Bridge Rectifiers
Magnetic field-resistant or welding-resistant proximity switches are used where strong magnetic fields can influence the function of the proximity switch. For example, they can be used in the field of strong magnetic coils as well as welding guns or welding electrodes with high welding currents. |
Phase Demodulator
The inductive proximity switch monitors and detects operating conditions on EAS overload clutches. Axial movements caused by overload or switching procedures are registered by the proximity switch. The signal can be used for further process controlling e.g. for drive switch-off. |
ROBA-multiswitch
The limit switch is used to monitor and measure axial or radial mechanical movements and adjustments e.g. on EAS-clutches. The device is suitable for clutches with a minimum stroke of 1.1 mm with radial actuation and 0.9 mm with axial actuation. |
 |
ROBA-switch
ROBA-switch fast acting rectifier units are used to connect DC units to alternating voltage supplies, for example electromagnetic brakes and clutches (ROBA-stop, ROBA-quick, ROBATIC), electromagnets, electrovalves etc. |
ROBA-switch 24V
ROBA-switch 24V fast switching modules are used to operate DC consumer units with overexcitation or power reduction, for example electromagnetic brakes and clutches (ROBA-stop, ROBA-quick, ROBATIC), electromagnets, electrovalves etc. |
Spark Quenching Unit
Reduces spark production on the switching contacts occurring during VDC inductive load switching
- Voltage limitation according to VDE0580 2000-07, Item 4.6
- Reduction of EMC-disturbance by voltage rise limitation, suppression of switching sparks
Reduction of brake engagement times by a factor of 2-4 compared to freewheel diodes |
ROBA-takt switch gear
This unit is used to start, stop and to position by switching and controlling the mayr-clutch-brake units. |
ROBA-takt Circuit Module
This device is used to start and stop mayr ROBA-takt circuit modules and mayr-clutch brake combinations.
It can be used for alternating 24 VDC coil switching, if a 24 VDC power supply is available. |
.jpg)
